|
Our software includes PC to rig interface features.
We had a lot of help from Phil, W1GEE, in getting our own rig
set up so that we could test and create the code for these functions. Phil was very responsive
and helpful with his e-mails. He clearly cares about his products
and takes his service seriously. Following that positive experience,
we were happy to offer other hams access to his interface
products via our website.
If
you are interested in taking advantage of the rig interface
features in our software - reading the band and frequency and
right clicking on DX spots to tune your rig to the spot frequency
- the following products should be a big help.
The
LCU-3 Interface Cable
The LCU-3 Interface Cable is functionally
equivalent to the radio manufacturer’s CAT interface, but costs considerably
less. Each cable is fitted with the
appropriate CAT port plug to connect directly to the radio CAT port. The LCU-3
has been designed to minimize RFI and is compatible with the
rig control features that are incorporated in N3FJP's Amateur
Radio Software. Each unit is tested prior to shipment and protected by a 90-day limited parts
and labor warranty.
Select the LCU-3 model from the list below and
specify whether a 9-pin or 25-pin serial connector is to be supplied (Note that
each LCU3 must have the software assert RTS in order for it to power up from
the serial port.):
LCU-3I
- Cable terminated with a 1/8” phone plug (both 9-pin and 25-pin serial connector versions
available) -
$45.00
Cable terminated with a 1/8” phone plug. Use with
IC-271 (A,E,H) (e), IC-471 (A,E,H) (e), IC-706 (all), IC-718, IC725, IC-726, IC-728,
IC-746, IC-46 PRO, IC-751 & IC-751A (e), IC-756 (all), IC-761, IC-765, IC-781,
IC-970, IC-R10, IC-R71 (A,E,H) (e), IC-R72, IC-R700, ICR7000, IC-R7100,
IC-7800, IC-R9000, TenTec Argonaut II, Delta II, Omni VI, Paragon and others.
(e)Requires Icom UX-14 Parallel to
serial converter.
LCU-3K
- Cable terminated with a Male 6-pin DIN plug (only available in 25-pin serial connector version)
-
$50.00
Cable terminated
with a Male 6-pin DIN plug. Use with TS-50 (f), TS-60 (f),
TS-140
(c), TS-440 (b), TS-450, TS-680(c), TS-690, TS-711 (d), TS-790, TS-811
(d), TS-850, TS-940 (a), TS-950, R-5000 (b) and others.
 Notes:
(a) requires IF-10B(b)
requires CHSET-1; (c) requires IF-10C; (d)
requires IF-10A; (e) requires UX-14 PCB; (f) requires IF-10D; (g)
has limited control capability.
CHSET-1
Interface - $15.00
Replaces
the IC-10. Consists of two IC’s and instructions.
LCU-3Y1 -
Cable terminated
with a Male 6-pin DIN plug
(both 9-pin and 25-pin serial connector
versions available) - $45.00
For use with FT-736 (g), FT-747, FT-767, FT-990, FT-1000/1000D, Heathkit SB-1400 and others with
DIN-6 CAT port.
LCU-3Y2 -
Cable terminated
with a Male 6-pin mini
DIN plug (both 9-pin and 25-pin serial connector
versions available) - $45.00
For use with
FT-757GXII, FT-840, FT-890, FT-900, and others with mini DIN-6 CAT
port.
LCU-3Y3 -Cable terminated
with Male 8-pin mini
DIN plug
(only 9-pin serial connector version
available) -
$40.00
The
LCU3-Y3 Interface Cable replaces the
Yaesu CAT-62 and converts the bi-polar signals of the computer’s RS-232 serial
port into TTL signals required by many Yaesu communications transceivers and
receivers. With the proper software, one
can control the radio with a computer.
Mode, frequency and other functions can automatically be controlled. The revolutionary new compact design
simplifies hookup and reduces clutter.
Power off the radio and computer, then simply plug one end into the
computer serial port (using an adapter if necessary) and the other end into the
radio CAT control port. Refer to the
radio instruction manual for the location of the port. The computer serial port powers the LCU3-Y3 Interface Cable. No battery or external power is needed.
Operational Notes:
The software used with this interface must assert RTS for
the unit to receive power. Be sure that the mini DIN-8 plug is properly seated into the
radio CAT socket.
The
LCU3-Y3 Interface Cable replaces the
Yaesu CAT-62. Yaesu radios have three
sizes of CAT ports The FT-736, FT-747, FT-767, FT-980. FT-990, FT-1000,
FT-1000D, Heath SB-1400, FRG-100, FRG-9600 have a standard 6-pin DIN CAT socket
and will require the LCU3-Y1 Interface
Cable. The FT-757GXII, FT-840,
FT-890 and FT-900 have a 6-pin mini
DIN
CAT socket and will require either the LCU3-Y2
Interface Cable or an LCU-AD adapter cable in addition to the
LCU3-Y1 Interface Cable. The FT-100, FT-817, FT-857 and FT-897 will
require the LCU3-Y3 Interface Cable.
The following rigs do not need the LCU3-Y1,
LCU3-Y2 or LCU3-Y3 Interface Cable: FT-847 (uses a standard 9-pin null-modem
cable); FT-920 (standard cable, NOT null modem); FT-1000MP (same as
FT-920). The LCU3-Y1 (Y2) Interface
Cables will not work with the FT-980, FT-575 or FT-757GX.
Warranty:
The LCU3-Y3
Interface Cable is warranted to be defect free for a period of 90 days from
the date of purchase by the original owner provided the unit has been
registered.
Other Products:
ADAPT-1
- Adapter Cable - $25.00
Adapter cable, which will allow the conversion
of one LCU3-Y to another CAT, port configuration. Specify configuration when ordering.
25
Pin to 9 Pin Serial Adapter Cable - $10.00
Short
cable for use with 9-pin serial ports.
PC
Serial Keying Module - $25.00
Cable
connects to the PC 9-pin Serial Port (DTR keying).
PC
Parallel Keying Module - $25.00
Cable
connects between a computer's parallel (printer) port and the
transceiver's straight key socket. Optical isolation protects
the parallel port.
PC
Serial Keying Module with DB-9 to DB-25 Adapter - $35.00
Serial
keyer with adapter which allows the keyer and LCU3 Interface connection to a single 9-pin serial
port.
Blaster
Adapter - $35.00
Allows RigBlaster
DTR keying and LCU3 rig control from a single DB9 serial port.
If
you have questions concerning any of these products or your
rig is not listed as supported, please contact Phil, W1GEE directly
via e-mail: w1gee@yahoo.com
for more information.
Product
Purchase
Options
Please
send Cash, Check, or Money Order payable to G. Scott Davis to
purchase these products.
Please add $5.00 for shipping/handling
per
order within the United States.
Drop ship orders outside the US are shipped via Air Post. Please add $10.00 shipping and handling per
item for international orders.
If ordering an LCU-3 interface cable,
please specify
the TYPE as listed above
and the model
of your rig.
Please be sure to include your call
sign and e-mail address with your request so we can process your
order promptly!
Send to the address below:
G.
Scott Davis, N3FJP
118
Glenwood Road
Bel
Air, MD 21014-5533
To
purchase
by credit card via PayPal, please click an icon below. Be sure to include your call
sign
in the message
section! PayPal will send you a Receipt of Payment within minutes
of your transaction. When we receive Notification of Payment from PayPal, we will promptly
forward your order to W1GEE via e-mail. If you have not received a confirmation within 24
hours, please send
us an e-mail.
A $5.00 shipping/handling fee has
been added to the purchase price below for single US orders.
If
you are ordering multiple products
to be shipped to the same address, or you are located outside
the US,
please use the "PayPal Buy Now" button below. When
using this button you must list the items you are purchasing
in the message
section and enter the total amount + shipping/handling ($5 US to one
address/$10 International).
These products are manufactured
by W1GEE and will be shipped directly from him. Any questions
regarding
these products should be e-mailed to w1gee@yahoo.com.
| 